Classe Audio CP-35 Manuel du propriétaire télécharger pdf (Page 6)

It may be used with CD players that have a

BALANCED output, or any other high level

BALANCED sources.

Tape In

The TAPE IN of the CP-35 preamplifier should

be connected to the LINE OUT or TAPE OUT of

the tape deck. The TAPE input does not appear

on the selector switch. It is activated by the

TAPE switch. (See FRONT PANEL CONTROLS:

TAPE BUTTON.)

IR In (and Out)

This will permit you to install an outboard

infra-red sensor and therefore be able to control

the CP-35 remotely from another room where

the outboard IR sensor has been installed. These

connections will be found below the AC power

inlet at the back of the unit (see fig.3).

OUTPUTS

The Classé CP-35 preamplifier has both line

level (single-ended) and BALANCED outputs

(see fig. 3). Both are working at all times, and

may be used separately, or simultaneously.

Tape Output

Whatever input is selected by the INPUT

SELECTOR will be fed to the TAPE OUTPUT jacks.

This should be connected to the TAPE IN or LINE

IN of the tape deck.

Line Level Outputs

Simply connect your LINE LEVEL interconnects to

the RCA output jacks marks LINE LEVEL OUTPUT

on the back of the CP-35.

Balanced Outputs

A BALANCED power amplifier and BALANCED

interconnects are also required. For use with a

BALANCED power amplifier other than Classé,

the wiring of the 3-pin XLR connectors must be

wired as follows:

• PIN 1: GROUND

• PIN 2: POSITIVE (NON-INVERTED) SIGNAL

• PIN 3: NEGATIVE (INVERTED) SIGNAL

If the pin configuration of the power amplifier

differs from above, the BALANCED interconnects

must be modified to accommodate the different

power amp.

Having confirmed the correct connections,

plug the XLR connectors of the BALANCED

interconnects into the locking XLR connector

on the rear of the CP-35 marked BALANCED

OUTPUT. (To remove the connectors, press

the tab above the connector.)

FRONT PANEL CONTROLS

Input Selector:

The input selector (see fig.4) has two buttons for

selecting the inputs; (<) and (>). Pressing the

< button. selects the input to the left of the

currently selected input, and pressing the >

button selects the input to the right of the

currently selected input. If the > button is

pressed when BAL1 is the current input then the

LINE1 input will be selected, and if the < button

when LINE1 is the current input then the BAL1

input will be selected. The < and > buttons

will select from five input connections on the

preamplifier, but not the TAPE, (see TAPE below).

Tape

In the SOURCE position (TAPE LED OFF), the

preamp will process the signal as chosen by the

INPUT SELECTOR. In the TAPE position (TAPE LED

ON (RED)), the preamp will process the TAPE

INPUT signal, overriding the INPUT SELECTOR.

Volume Control

The VOLUME CONTROL varies the output level of

both channels simultaneously. It can be operated

by remote using the hand held control unit (see

fig.4) or manually turning the control knob at the

preamp. The volume control has a total of

120 steps of level adjustments form 0 to 60

in 0.5 stepped increments. When the unit is

plugged in, the display will count down from

20 to 0. When the countdown has resumed, the

volume will be automatically at zero (0) and the

preamp will be muted and therefore show MUTE

at the right of the digit display. When you un-

mute, the volume will return to the same level

it was at before you turned on the mute mode.

PLEASE NOTE: It is normal for the volume to

stay at the same level if you turn the VOLUME

knob extremely slowly.

Mute

Press the MUTE button (see fig. 4) to temporarily

set the VOLUME to 0. When activating the MUTE

function , MUTE will light up at the right of the

volume display digits. Switching can be done by

either pushing the MUTE button momentarily on

the CP-35 faceplate or on the remote handset.

The volume setting is memorised when the

unit is in mute mode; thus Volume will return

to the same level it was playing at prior to

muting when you turned off MUTE mode.

(see DISPLAY section)

PLEASE NOTE: The display will change to Display

Full Off mode after the unit has been in MUTE

mode for one hour.

NOTE: When the CP-35 is in the mute position,

and the volume control is turned up using the

volume control on the unit or the remote control,

the play mode is automatically selected.

CAUTION: Make sure the preamp is in

MUTE(ON) when making or changing any

connections. This includes all inputs and outputs,

as well as A.C. linecord.

Remote Handset

The remote handset will permit you to access

remotely all the functions found on the front

panel of the unit: VOLUME UP or DOWN, MUTE

ON or OFF, DIRECT ACCESS for all the INPUTS

and TAPE monitor. In addition to all these

functions, the button marked DISPLAY will

permit you to select through the four display

modes on the unit.

PLEASE NOTE that the DISPLAY function can

only be activated through the remote handset.

To access the batteries, unscrew the back plate

of the remote handset (see fig. 2)

Balance Control (on Remote Handset only):

The balance control found on the remote

handset only permits equal output of each

channel in the center (00.0) position without

additional loading to the signal. When shifted

to the left or right, it merely attenuates the

opposite channel. When operating the balance

control, the right of the display will show

BALANCE. By shifting the balance to either

sides (left or right) one of the two LEDs located

on either sides of the DIGIT display will light

accordingly to the side on which the balance is

shifted. The amount of attenuation will be show

on the DIGIT display in increments of 0.5 up

to19.5. If the balance control if shifted to the

maximum (19.5) on either sides, the digit display

will show OFF which means that the opposite

channel now gives out no signal since the

balance is completely shifted to one side.

Display (on Remote Handset only)

Pressing the DISPLAY button on the remote

handset (see fig. 1) allows you to control the

brightness of the display. There are 3 levels of

brightness; Display On, Display Medium On,

Display Low On or Display Full Off. Repeated

pressing of the DISPLAY button will cycle through

the four modes, from Display Full On to Display

Full Off. Pressing DISPLAY when the display is

at Full Off will cause the display to go back to

Display Full On.

NOTE: Three (3) LEDs will continue to be lit on

the display when it is in Display Full Off mode

to let you know that the CP-35 is still on and

operating. When in Display Full Off mode and

any other functions are used, such as changing

volume or selecting a new source, the display will

light at Display Full On mode for five seconds

and then go back to Display Full Off mode. The

display will automatically go to Display Full Off

mode after the MUTE mode has been activated

for one hour.

CP-35 FEATURES:

Remote control featuring adjustments for

volume, direct access input selection, tape,

display and mute. Contoured slimline chassis.

Inputs featuring LINE1, LINE2, LINE3, LINE4 and

BAL1 inputs. Both BALANCED and LINE LEVEL

outputs. Front panel adjustments include input

selection, volume and mute. Special Classé front

panel in Soft Shadow Silver with Satin Black

display panel plate.

Notice to all Classé Product owners:

Thank you for your purchase of a Classé

Audio component.

All of us at Classé have taken extreme care to

ensure that your purchase will become a prized

investment. We are proud to inform you that all

Classé Audio components have been officially

1 2 3 4 5 6 7 8 9 10 11 ... 22 23

Commentaires sur ces manuels

Pas de commentaire

Classe Audio CP-35 Manuel du propriétaire Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Amplificateurs audio Classe Audio CP-35